Perancangan Mesin 3D Printing Model Cartesian

Hari Din Nugraha, Deny Poniman Kosasih

Abstract


3D Printing merupakan salah satu terobosan bidang manufaktur khususnya teknik additive manufacturing, yang proses menjadikan dalam file digital menjadi suatu objek padat 3 dimensi berdasarkan susunan lapisan (layer) bahan. Tujuan penelitian ini adalah merancang mesin 3D Printing dengan model siste cartesian dan pengujian sistem menggunakan aplikasi repitier host. Penlitian menggunakan jenis penelitian Design-Based-Research (DBR).  Hasil penelitian di jabarkan sebagai berikut; (1) proses perancangan desain mesin 3D printing didapatkan hasil area kerja panjang 30 cm lebar 30 cm dan tinggi 30 cm, sehingga dari rencana area kerja tersebut bisa ditentukan komponen mekanis, komponen rangka utama dan komponen pelengkap lainya. (2) Software repitier host dapat digunakan sebagai simulasi model cartesian. Repitier dapat digunakan cocok digunakan menggunakan bahan dari Polilactid Acid (PLA) dan hasil warna yang lebih sempurna dan beragam. (3) Pada hasil pengujian terdapat stringing pada hasil simulasi produk, hal ini disebabkan karena pengaturan retraksi dan suhu temperatur yang tinggi

Keywords


Mesin 3D Printing, Cartesian, additive manufacturing

Full Text:

PDF

References


H. Yuk et al., “3D printing of conducting polymers,” Nat. Commun., vol. 11, no. 1, pp. 4–11, 2020, doi: 10.1038/s41467-020-15316-7.

A. A. Nurul Amri and W. Sumbodo, “Perancangan 3D Printer Tipe Core XY Berbasis Fused Deposition Modeling (FDM) Menggunakan Software Autodesk Inventor 2015,” J. Din. Vokasional Tek. Mesin, vol. 3, no. 2, pp. 110–115, 2018, doi: 10.21831/dinamika.v3i2.21407.

Y. Zhang, Y. Zhang, W. She, L. Yang, G. Liu, and Y. Yang, “Rheological and harden properties of the high-thixotropy 3D printing concrete,” Constr. Build. Mater., vol. 201, pp. 278–285, 2019, doi: 10.1016/j.conbuildmat.2018.12.061.

M. Kaszyńska et al., “Evaluation of suitability for 3D printing of high performance concretes,” MATEC Web Conf., vol. 163, pp. 1–8, 2018, doi: 10.1051/matecconf/201816301002.

B. J. Brooks, K. M. Arif, S. Dirven, and J. Potgieter, “Robot-assisted 3D printing of biopolymer thin shells,” Int. J. Adv. Manuf. Technol., vol. 89, no. 1–4, pp. 957–968, 2017, doi: 10.1007/s00170-016-9134-y.

M. Abdul and M. Amrullah, “Rancang Bangun Prototipe Printer 3 Dimensi ( 3D ) Tipe Cartesian Berbasis Fused Deposition Modelling ( Fdm ) Naskah Publikasi Tugas Akhir,” 2018.

Y. Tlegenov, G. S. Hong, and W. F. Lu, “Nozzle condition monitoring in 3D printing,” Robot. Comput. Integr. Manuf., vol. 54, no. December 2017, pp. 45–55, 2018, doi: 10.1016/j.rcim.2018.05.010.

B. M. Schmitt, C. F. Zirbes, C. Bonin, D. Lohmann, D. C. Lencina, and A. Da Costa Sabino Netto, “A comparative study of cartesian and delta 3d printers on producing PLA parts,” Mater. Res., vol. 20, pp. 883–886, 2017, doi: 10.1590/1980-5373-mr-2016-1039.

A. Prakasa, S. P. Sutisna, and A. R. Ahmad, “Penentuan Setting Optimal Mesin 3D Printer Berbasis Fused Deposition Modeling Menggunakan Metode Taguchi,” AME (Aplikasi Mek. dan Energi) J. Ilm. Tek. Mesin, vol. 4, no. 2, 2018, doi: 10.32832/ame.v4i2.1538.

G. Gaal et al., “Simplified fabrication of integrated microfluidic devices using fused deposition modeling 3D printing,” Sensors Actuators, B Chem., vol. 242, pp. 35–40, 2017, doi: 10.1016/j.snb.2016.10.110.

Z. Rahman, S. F. Barakh Ali, T. Ozkan, N. A. Charoo, I. K. Reddy, and M. A. Khan, “Additive Manufacturing with 3D Printing: Progress from Bench to Bedside,” AAPS J., vol. 20, no. 6, pp. 2–14, 2018, doi: 10.1208/s12248-018-0225-6.

S. Mocahmad Diki Muliyawan, Gatoto Eka Pramono, “Rancang Bangun Konstruksi Rangka Mesin 3D Printer Tipe Cartesian Berbasis Fused Deposition Modelling (FDM),” J. Tek. Mesin, vol. 3, no. 4, 2017., pp. 252–257,

R. C. Luo, L. C. Hsu, T. J. Hsiao, and Y. W. Perng, “3D Digital Manufacturing via Synchronous 5-Axes Printing for Strengthening Printing Parts,” IEEE Access, vol. 8, 2020, pp. 126083–126091, doi: 10.1109/ACCESS.2020.3007772.

Luki Aditya, “Prototipe 3D Printer Berbasis Mikrokontroler,” President University, 2019.

N. A. Bin Sukindar, M. K. A. M. A. Bin, B. T. B. Hang Tuah Bin, C. N. A. J. Binti, and M. I. S. I. Bin, “Analysis on the impact process parameters on tensile strength using 3d printer repetier-host software,” ARPN J. Eng. Appl. Sci., vol. 12, no. 10, 2017, pp. 3341–3346.

A. Elkaseer, S. Schneider, and G. Scholz, “applied sciences Experiment-Based Process Modeling and Optimization for High-Quality and Resource-E ffi cient,” Appl. Sci., 2020.




DOI: http://dx.doi.org/10.31543/jtm.v5i1.557

Refbacks

  • There are currently no refbacks.


License URL: https://creativecommons.org/licenses/by-nc/2.0/

View JTM Statistics

 

Flag Counter

Online ISSN: 2548-3854

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 2.0 Generic License.